'Fertigation' is the technique of supplying dissolved fertiliser to crops through an irrigation system.
When combined with an efficient irrigation system both nutrients and water can be manipulated and managed to obtain the maximum possible yield of marketable production from a given quantity of these inputs.
Often, solid fertiliser side-dressings are timed to suit management constraints rather than the horticultural requirements of the crop. Most growers will have experienced the dilemma of spreading fertiliser the day before heavy rain and then wondering how much of the fertiliser is either washed from the crop in run-off or leached below the root zone.
Continuous small applications of soluble nutrients overcome these problems, save labour, reduce compaction in the field, result in the fertiliser being placed around the plant roots uniformly and allow for rapid uptake of nutrients by the plant.
To capitalise on these benefits, particular care should be taken in selecting fertilisers and injection equipment as well as in the management and maintenance of the system.
The fertiliser requirements will depend on leaf analysis. The type of fertilisers you choose will be dictated by price and the results of the analysis of your irrigation water.
The fertiliser products which can be used are limited to those that are readily soluble. The many commercially formulated soluble fertilisers available to growers include DRIPpHLO®, GF Flowfeed®, Sustain®, Reef® fertilisers, and Supa Crop®. Many of these formulations are prepared for specific crops, or combinations can be used depending on the crop cycle. They have the advantage of being stable and highly soluble, dissolving rapidly and providing a balance of nutrients so only one product is handled. However, they are generally more expensive per unit of nutrient than are standard fertilisers.
|Material||Average % nutrient composition of material|
|Ammonium nitrate (Nitram®)||34|
|Sulfate of ammonia||20.0||24 sulfur|
|Mono-ammonium phosphate MAP||12.5||22|
|Di-ammonium phosphate DAP||19||20|
|Muriate of potash (KCl)||50|
|Potassium nitrate (KNO3)||13||38|
|Sulfate of potash K-Spray (K2SO4)||42||18 sulfur|
Plants absorb and use most of the nitrogen as nitrate or ammonium ions.
The main types of nitrogen are:
Urea is commonly used and preferred because:
Compared with ammonium nitrogen, which can be held on clay and organic particles, and with nitrate, which moves freely and can be leached quickly, moving to the perimeter of the wetted zone in the soil, urea offers the best value.
In colder soil conditions during winter, nitrate forms of nitrogen are preferred.
Phosphorus supply is usually provided by:
The possibility of precipitation of insoluble phosphates is high when using MAP or DAP with irrigation water that is high in calcium or magnesium. This will cause clogging of outlets and pipelines.
Phosphoric acid provides the advantage of cleansing lines and sprays and is a concentrated liquid offering ease of use. Providing the pH of the water is kept low, clogging or precipitation should not be a problem. This can be done by using more acid. Phosphoric acid must be injected at a point beyond any metal connections or filters in order to avoid corrosion.
If using MAP or DAP be aware that these fertilisers do not dissolve completely so your mixing tank will need facilities for cleaning out the undissolved residue which collects at the bottom of the tank.
MAP or DAP, although not as soluble as phosphoric acid, have the added bonus of also supplying nitrogen.
One litre of phosphoric acid (this contains 60% H3PO4) weighs 1.55 kg and is equal to 20% P (actual) and therefore equals 0.31 kg of P/litre. Single super equals 9% P, so 1 kg = 0.09 kg of P.
Therefore, one litre of phosphoric acid is equivalent to:
Irrigators can choose from:
Potassium nitrate is the recommended source of potassium for use in fertigation programs because of its solubility and added bonus of providing nitrogen. It is, however, the most expensive of the potassium fertilisers.
Potassium sulfate is inferior to the other two sources as its solubility is not as high.
Potassium chloride is the most economic of the potassium fertilisers, but can be a problem with crops that are sensitive to high chlorine concentrations such as stone fruit, pecans, citrus, strawberries and avocados. For these crops a mixture of potassium sulfate and potassium chloride can be used to reduce costs.
Soluble forms of the three lesser macronutrients - calcium, magnesium and sulfur - do exist but these are much more expensive, not always compatible with mixes and can cause precipitation and clogging. The conventional forms of these nutrients - lime, gypsum and dolomite - should be spread in the normal way.
Chelates and sulfate compounds of various micronutrients are generally used for correcting micronutrient deficiencies. These compounds should be predissolved and metered into your tank as a liquid.
The micronutrients that can be supplied via your irrigation system include: copper, iron, zinc, manganese, boron and molybdenum.
|Crop King product||Maximum amount (kg) dissolved in 100 L at 20°C||Time to dissolve (min)||pH of the solution||Insolubles (%)||Comments|
|Urea||105||20(a)||9.5||negligible||Solution cools as urea dissolves.|
|Ammonium nitrate [Nitram® NH4NO3]||195||20(a)||5.62||Corrosive to galvanised iron and brass. Solution cools as product dissolves.|
|Sulfate of ammonia [(NH4)2SO4]||43||15||4.5||0.5||Corrosive to mild steel.|
|Mono-ammonium phosphate [MAP]||40||20||4.5||11||Corrosive to carbon steel.|
|Di-ammonium phosphate [DAP]||60||20||7.6||15||Corrosive to carbon steel.|
|Muriate of potash [KCl]||34||5||7.0–9.0(b)||0.5||Corrosive to brass and mild steel.|
|Sulfate of potash [K2SO4]||11||5||8.5–9.5(b)||0.4–4(b)||Corrosive to mild steel concrete.|
|K-spray [K2SO4]||11||1||8.5–9.5(b)||0.4–4(b)||Corrosive to mild steel concrete.|
|Potassium nitrate [KNO3]||31||3||10.8||0.1||Solution cools as product dissolves. Corrosive to metals.|
The information in Table 3 is an extract from Table 11, Hardesty, J. O., Dickey, G. F. and Olive, B. M., Production Methods - Potassium Nitrate in Mixed Fertilizers, Farm Chemicals, February 1961.
The information in Table 4 is an extract from data published in February 1967 by HaifaChemicals Ltd, Israel.
|% Urea (by weight)||% Potassium nitrate (by weight)||Solubility (g/100 g H2O)|
Modern fertigation should be able to regulate:
Four systems are generally used:
The selection of the correct injection equipment is just as important as the selection of the correct nutrient. Incorrect selection of equipment can damage parts of the irrigation equipment, affect the efficient operation of your irrigation system or reduce the effectiveness of the nutrients.
The three usual methods of injection are:
Suction of fertiliser through the intake of the pump is a common method of application and is the simplest method. The pumping unit develops a negative pressure in its suction pipe (unless the suction is flooded). This negative pressure can be used to draw fertiliser solutions into the pump. A pipe or hose delivers the fertiliser solution from an open supply tank to the suction pipe. The rate of delivery is controlled by a valve. This connection must be tight to prevent air entry into the pump.
Another hose or pipe connected to the discharge side of the pump can fill the supply tank with water. A high-pressure float valve can be used to regulate this inflow into the tank.
If necessary the system can be automated with a direct-acting solenoid valve. For multiple block usage, two or more tanks can be set up in series and operated when required.
A pressure differential tank system is based on the principle of a pressure differential being created by a valve, pressure regulation, elbows or pipe friction in the mainline, forcing water through a bypass pipe into a pressure tank and out again, carrying a varying amount of dissolved fertiliser.
A pressure differential venturi system can be installed as a bypass or inline. The venturi causes a rapid change in velocity producing a reduced pressure (vacuum) which draws the fertiliser solution into the line.
Injection rates of 2 litres to 3000 litres per hour can be achieved.
This is the most common method of injection of fertiliser into irrigation systems. Injection energy is provided by electric motors, impeller-driven power units and water-driven hydraulic motors.
The pumps are usually rotary, gear, piston or diaphragm-type which deliver fertiliser solution from the supply tank into the pressurised mainline. This method can be very accurate. Pumps are generally not simple in design and can include a number of moving parts, so wear and breakdown are more likely.
The three systems available are electric injection pumps, piston-activated pumps and diaphragm-activated pumps. Piston-activated and diaphragm- activated pumps are both hydraulic injection pumps; these dominate the fertigation market at present.
Electric injection pumps include single or multiple piston, diaphragm, gear and roller pumps. These can be regulated to achieve the desired rate by:
Piston-activated pumps - in which irrigation water operates a hydraulic motor that pumps the fertiliser solution into the system. Since the pump’s maximum rate of injection is proportional to the pressure in the mainline, the required injection rate is easily adjusted by throttling the injection line by means of a valve fitted to the water main, and as the injection rate per pulse is known, the exact application of nutrients can be readily calculated. For high injection rates, two or more units can be operated in parallel. Injection rates of up to 320 litres/hour are possible.
Diaphragm-activated pumps - water pumped into the lower chamber activates a rubber diaphragm in the drive unit which forces the diaphragm up, and in doing so via a drive rod, forces the fertiliser out of the injector into the irrigation system. On the return stroke the spent drive water is discharged from the lower chamber of the drive unit while simultaneously fertiliser solution is drawn into the injector. The cycle is automatically repeated. Injection rates from 3 litres to 1200 litres per hour are possible. There is an upper limit to the pressure available and they might not operate on high head systems.
The effectiveness of fertigation is often dependent on the effectiveness of the irrigation system. The full advantages of irrigation and fertigation only become evident if the correct irrigation design is employed to meet plant requirements and to distribute water and fertiliser evenly.
Because of the corrosive nature of many fertilisers, the components of the irrigation system that come into contact with corrosive solutions should consist of stainless steel, plastic or other non-corrosive materials. Concentrations of total nutrients in the mainline should not exceed 5 grams/litre. Always mix fertilisers in sufficient volume of water. The following formula can be used to determine the injection rate:
Maximum injection rate = (5 × Q × L) ÷ (F × 60)
Q = irrigation pump discharge in litres per second
L = fertiliser tank volume in litres
F = amount of fertiliser in grams
For each crop there are many fertiliser programs. Fertigation allows you to change your program during the growing season, adjusting it to suit fruit, flower, shoot and root development. A program should be developed on the basis of leaf and soil analysis and tailored to suit your actual crop requirements.
The majority of injectors available today can generally incorporate automatic operation by fitting pulse transmitters which convert injector pulses into electric signals. These signals then control injection of preset quantities or proportions relative to flow rate of the irrigation system.
Injection rates can also be controlled by flow regulators, chemically resistant ball valves or by electronic or hydraulic control units and computers.
If fertilisers are not completely dissolved and mixed prior to injection into the system, this may result in varying concentrations applied or blockages within the system.
Suitable anti-siphoning valves or non-return valves should be installed where necessary to prevent backflow or siphoning of water, fertiliser solution, chemical solution etc. into fertiliser tanks, irrigation supply, household supply, stock supply and so on.
Fertigation increases the quantity of nutrients present in an irrigation system and this can lead to increased bacteria, algae and slime in the system. These should be removed at regular intervals by injection of chlorine or acid through the system.
Chlorine injection should not be used while fertiliser is being injected into the system as the chlorine may tie up these nutrients making them unavailable to the plant.
Systems should always be flushed of nutrients before completion of irrigation.
Before commencing a fertigation program, check fertiliser compatibilities and solubility.
During the irrigation season it is important to monitor:
®registered trade name